Ug-value and edge heat loss of triple glazed insulating glass units: A comparison between measured and declared values

Ghazi Wakili, Karim; Rädle, Wolfgang; Krammer, A.; Uehlinger, Andrea; Schüler, A.; Stöckli, Thomas (2021). Ug-value and edge heat loss of triple glazed insulating glass units: A comparison between measured and declared values Journal of Building Engineering, 2021(44), pp. 1-7. Elsevier https://doi.org/10.1016/j.jobe.2021.103031

[img] Text
ghazi-wakili-et-al-triple-glazing-jbe-2021.pdf - Published Version
Restricted to registered users only
Available under License Publisher holds Copyright.

Download (3MB) | Request a copy

Triple glazed low-e coated insulating glass units with argon filling of five different suppliers on the European market with a declared thermal transmittance in the undisturbed centre of glass (Ug-value) of 0.6 W/m2K have been purchased from resellers and tested in a guarded hot plate at vertical position. The measured results showed deviations towards higher values for all 5 types. These have been analysed by recurring to the determination of the two main factors namely the gas mixture in the two cavities and the emissivity of the coated glass panes. Nondestructive measuring methods for gas mixture analysis and standardized calculation methods for the Ug-value have been used to analyse the influence of these two factors. In a further step the edge heat loss due to the spacer of the insulating glass units has been measured by using two “halves” of each glazing type with a double edge running through the middle of the measured sample. This was done following a standardized test method for the determination of the edge heat loss of Vacuum Insulation Panels (VIP). Finally, pieces of the coated glass panes were cut out of the glazing units and their emissivity measured with both an infrared spectrometer and an emissiometer. Results showed an increased emissivity value for the coated surfaces leading to higher Ug values than measured. This is partly due to the exposure to air and the possible degradation of the coating. The investigation shows non-destructive emissivity determination is needed to get more accurate in-situ emissivity values of the coatings.

Item Type:

Journal Article (Original Article)

Division/Institute:

School of Architecture, Wood and Civil Engineering
School of Architecture, Wood and Civil Engineering > Institute for Timber Construction, Structures and Architecture
School of Architecture, Wood and Civil Engineering > Institute for Timber Construction, Structures and Architecture > Windows, Doors and Façades
School of Architecture, Wood and Civil Engineering > Institute for Timber Construction, Structures and Architecture > Timber Construction
School of Architecture, Wood and Civil Engineering > Institute for Timber Construction, Structures and Architecture > Building Physics
School of Architecture, Wood and Civil Engineering > Institute for Timber Construction IHB
School of Architecture, Wood and Civil Engineering > Institute for Timber Construction IHB > Building Envelope and Building Physics group FGGB
School of Architecture, Wood and Civil Engineering > Institute for Timber Construction IHB > Timber Structures group FGH

Name:

Ghazi Wakili, Karim;
Rädle, Wolfgang;
Krammer, A.;
Uehlinger, Andrea;
Schüler, A. and
Stöckli, Thomas

Subjects:

T Technology > T Technology (General)
T Technology > TH Building construction

ISSN:

2352-7102

Publisher:

Elsevier

Language:

English

Submitter:

Wolfgang Rädle

Date Deposited:

17 Jan 2022 14:44

Last Modified:

04 Nov 2022 09:41

Publisher DOI:

https://doi.org/10.1016/j.jobe.2021.103031

Uncontrolled Keywords:

Ug-value guarded hot plate gas mixture surface emissivity linear thermal transmittance triple glazing

ARBOR DOI:

10.24451/arbor.16214

URI:

https://arbor.bfh.ch/id/eprint/16214

Actions (login required)

View Item View Item
Provide Feedback